Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
We have unearthed this great article pertaining to Tools You Need to Install a New Bathtub directly below on the web and think it made perfect sense to talk about it with you on this site.
Installing a bathtub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging project. If the old tub is easily easily accessible, the job can relocate easily; if you need to open up a wall surface to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the new one. Ensure you have qualified yourself for the job and also fit trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already acquired a brand-new bathtub and also don't need to change the arrangement of your previous water supply pipelines.
Your devices and also product list must make up the following:
Preparing for the Installation
Firstly, the sustaining framework supplied with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, place the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub needs to wait till the tub has been used at the very least once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the faucet in place with the manufacturer given backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before sealing, to permit the movement experienced when the tub remains in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof glue and cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you liked our topic about How to Install a Bathtub Yourself. Thanks a lot for finding the time to browse our blog. Loved our review? Please share it. Let other people discover it. We appreciate reading our article about How to Install a Bathtub.
Schedule Estimate Report this page